Size :7.11 MB
Page{s) : 24
Create Date : February 23, 2015

Transcript of Vulcan-Hart VW3S ML-126504 Operating instructions

INSTALLATION & OPERATION MANUAL VW & VSL SERIES DRAWER WARMERS VCW1, VCW2 CHIP WARMERS MODELS: CHIP WARMERS: VCW1 ML-138038 VCW2 ML-138041 DRAWER WARMERS: CAFE': VW1S ML-126500 VW2S ML-126502 VW3S ML-126504 VW4S ML-126506 CAFE' BUILT-IN: VW1SB ML-126501 VW2SB ML-126503 VW3SB ML-126505 VW4SB ML-126507 SLIMLINE LOW PROFILE: SLIMLINE BUILT-IN: VW1C ML-126516 VW1CB ML-126517 VW2CB ML-126518 VW2C ML-126518 R-SERIES BUILT-IN: VSL1 VW1DB ML-126509 VSL2 VW2DB ML-126511 VW3DB ML-126513 R-SERIES: ML-126508 VW4DB ML-126515 ML-126510 VW1D ML-126512 VW2D ML-126514 VW3D VW4D VULCAN-HART 3600 NORTH POINT BLVD. DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC BALTIMORE, MD 21222 www.vulcanequipment.com Vulcan (c)2015 All Rights Reserved F-31086 (02-15)

VW, VSL & VCW SERIES F-31086 (02-15) TABLE OF CONTENTS IMPORTANT FOR YOUR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TRIM KIT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ELECTRICAL REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 THERMOMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 THERMOSTAT SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DAILY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 HEAVY-DUTY CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 STAINLESS STEEL CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PRESERVING & RESTORING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 HEAT TINT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 SERVICE & PARTS INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2

VW, VSL & VCW SERIES F-31086 (02-15) GENERAL INTRODUCTION It is suggested that you thoroughly read Vulcan-Hart Drawer Warmers and Chip this entire manual and carefully follow all Warmers are produced with quality of the instructions provided. workmanship and material. Proper installation, usage, and maintenance of The VW Series Drawer Warmers your warmer will result in many years of provide an efficient means of holding a satisfactory performance. variety of prepared hot food products at proper temperatures until serving. INSTALLATION Before installing, verify that the electrical 3. Remove legs from drawer of service agrees with the specifications on warmer. the rating plate located on the lower back corner of the warmer. If the supply 4. Secure legs to the bottom of and equipment requirements do not warmer by screwing legs into the agree, do not proceed with unpacking holes provided. and installation. Contact your Vulcan- Hart Customer Service Department 5. Remove any and all packaging immediately. materials in drawers. UNPACKING: 6. Peel off vinyl protection film. The Warmer was inspected before 7. Thoroughly clean the warmer as leaving the factory. The transportation company assumes full responsibility for described in the cleaning instruct- safe delivery upon acceptance of the ions. shipment. Immediately after unpacking, check for possible shipping damage to CLEANING: the warmer. The warmer should be thoroughly cleaned prior to putting into service. If the warmer is found to be damaged, save the packaging Use a mild soap and water solution to material and contact the carrier clean the interior drawer inserts of the within 15 days of delivery. unit. Never use harsh chemicals or abrasive pads to clean the unit. Carefully unpack warmer and place in a work accessible area. LOCATION: 1. Remove banding holding the For efficient warmer operation, choose a location that will provide easy loading carton to the pallet. and unloading without interfering with 2. Carefully remove warmer from the final assembly of food orders. carton and place on floor or table. The installation location must allow adequate clearances for servicing and proper operation. 3