Size :531.4 KB
Page{s) : 1
Create Date : June 13, 2011

Transcript of Whirlpool Wgd9550wl Quick Specs

Duet Steam and Non-Steam Electronic Gas Dryer PRODUCT MODEL NUMBERS Dryer dimensions OVERALL DIMENSIONS WGD9450W, WGD9470W, WGD9550W, STEAM - 529/16" Custom undercounter installation-dryer only WGD9600T, WGD9750W, WGD9610X (1335 mm) Gas supply: This dryer is equipped for use with Natural NON-STEAM - 511/2" gas. Dryer can be converted to L.P. gas. When rigid (1308 mm) pipe is used it should be 1/2" IPS. When acceptable 38" to the gas supplier and local codes, 3/8" approved (965 mm) tubing may be used for lengths under 20 ft (6.1 m). For lengths over 20 ft (6.1 m), larger tubing should be 38" 1"* 27" 1"* used. Pipe-joint compounds resistant to the action of (965 mm) L.P. gas must be used. An individual manual shutoff (25 mm) (686 mm) (25 mm) valve must be installed within 6 ft (1.8 m) of the dryer in accordance with the National Fuel Gas Code ANSI Most installations require a minimum Z223.1. 5" (127 mm) clearance behind the dryer for *STEAM - 329/16" 27" the exhaust vent with elbow. See Installation (827 mm) (686 mm) Electrical: A 120-volt, 60 Hz, AC-only, 15 or 20 amp Instructions, "Venting Requirements." fused electrical supply is required for gas dryers, 30 NON-STEAM - 311/2" amp for electric dryers. A time-delay fuse or circuit (800 mm) breaker and a separate circuit are recommended. Water (Steam models only): The dryer must be For closet installation, with a door, the minimum ventilation openings in the top and connected to the cold water faucet using new inlet bottom of the door are required. Louvered doors with equivalent air hoses. Do not use old hoses. Do not overtighten. ventilation openings are acceptable. Damage to the coupling can result. 6" Exhaust venting: Exhaust your dryer to the outside. 3" 14" max. (152 mm) 4" (102 mm) diameter vent is required. Rigid or flexible (76 mm) (356 mm) metal exhaust vent must be used. Do not use plastic 76" or metal foil vet. Exhaust hood must be at least 48 in.2 * 18" max. (1930 mm) 12" (305 mm) from the ground or any object that (310 cm2) (457 mm) may be in the path of the exhaust. Hood styles: A & B are recommended. B 4" C (102 mm) 24 in.2 * 3" (155 cm2) (76 mm) A 1" 27" 1" 21/2" STEAM - 329/16" STEAM - 51/2"** (25 mm) (686 mm) (25 mm) (827 mm) (140 mm) 4" (64 mm) (102 mm) NON-STEAM - 311/2" NON-STEAM - 5"** A. Louvered hood 4" B. Box hood (800 mm) (127 mm) (102 mm) C. Angled hood (acceptable) For dryer on pedestal; cabinet installation, with a door, the minimum ventilation The vent system chart provides venting requirments openings in the top are required. that will help to achieve the best drying performance. 7"* (178 mm) Vent system chart: 7"* NOTE: Side and bottom exhaust installations have (178 mm) a 90 turn inside the dryer. To determine maximum exhaust length, add one 90 turn to the chart. 14"* max. (356 mm) Number of Type of Box or Angled 18"* max. 9"* 90o turns vent Louvered hoods (457 mm) (229 mm) or elbows hoods 0 Rigid metal 64 ft (20 m) 58 ft (17.7 m) 1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m) 2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m) 3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m) 4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m) 1"* 27" 1"* STEAM - 329/16" 5" (25 mm) (686 mm) (25 mm) (827 mm) (127 mm) NON-STEAM - 311/2" (800 mm) 1" 37/16" 33/8" *Required spacing **For side or bottom venting, 0" (0 mm) spacing is allowed. (25 mm) (87 mm) 1" (86 mm) Select the route that will provide the straightest and most direct path outdoors. (25 mm) 75/8" Plan the installation to use the fewest number of elbows and turns. (194 mm) Use the fewest 90 turns possible. 14" Side View (356 mm) Do not use vent runs longer than specified in vent length chart. Back View Determine the number of elbows you will need. Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation W10255469B our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. 06/2011