Size :3.19 MB
Page{s) : 2
Create Date : January 18, 2007

Transcript of Canon DR-2050SP User`s guide

Document Scanner DR-2050C/SP 3. Open the front cover at (1) and (2), and remove the orange tape fastening the Installing the Software 7. Click [Finish] to complete the installation. Easy Start Guide roller cover. Install the software before connecting the scanner to the computer. Next, the installation wizard for CapturePerfect 3.0 appears. Thank you for purchasing the Canon DR-2050C/DR-2050SP Document Scanner. This Easy 4. Open the roller cover. Warning Start Guide describes the procedure for setting up the scanner for use. Follow the 8. Click [Next]. procedures outlined in this Easy Start Guide to set up the scanner. Details on using the Before installing the software, make sure your computer is correctly running one of scanner are described in the User's Guides packaged with the scanner. Before you use the the following versions of Windows. For details, refer to the DR-2050C/DR-2050SP 9. Read the software license agreement, and scanner, make sure to thoroughly read the User's Guides. User's Guide. * Windows 98SE click [Yes] if you consent to the conditions of Checking the Accessories * Windows Me the software. * Windows 2000 Professional SP4 or later When you unpack your scanner, make sure that it contains all of the following accessories. If * Windows XP Home Edition SP2 or later 10. Check the destination folder and click [Next]. any of the items listed below are missing or damaged, contact your local authorized Canon * Windows XP Professional SP2 or later dealer or service representative. Installation of CapturePerfect 3.0 starts. Do not connect the scanner to the computer before installing the software. If you connect the scanner and turn it ON before you install the software, a wizard screen 11. Click [Finish] to complete the installation of will appear. If this wizard appears, click [Cancel] to exit the wizard, and then turn the scanner OFF. CapturePerfect 3.0. USB Cable 12. Next, installation of OmniPage SE starts. DR-2050C/DR-2050SP Feed Roller Type A/Type B AC Adapter/Power Cord Follow the messages on the screen to proceed with the installation. (Length: 6 ft. (1.8 m)) (Connected length: 8 ft. 6 in. (2.6 m)) 5. Lower the roller lock lever (1), and slide it towards the left (2). 13. When all installations are complete, the Document Easy Start Guide DR-2050C/DR-2050SP Adjustment Sheet 6. Load the feed roller, align the notch on the roller with the shaft on the scanner Wizard Screen (Windows 2000) Guide Adapter Be sure to log on with administrator privileges when logging on to Windows. Installation completed screen appears. (this document) User's Guide body. Close all other applications before installing the software. Click [Exit] to exit the installer. (Click [Back] to return to the menu screen.) 0880281099-L5T1P7-BR01 1. Turn ON your computer. 2. Insert the DR-2050C Setup Disc into the 14. Remove the setup disc, and finish the CANON CANADA INC. 9Z9 6390 DIXIE RD PC's CD-ROM drive. software installation. MISSISSAUGA ON L5T The setup wizard automatically starts up when you insert the CD-ROM into the CD- Note DR-2050C Adobe Acrobat Warranty Card Registration Card ROM drive. If the setup wizard does not When software is installed the icons are added to the Program menu. Setup Disc start up, execute setup.exe in the CD-ROM. Setup Disc (U.S.A. and Canada only) (U.S.A. and Canada only) (Windows 2000) 3. Click [Typical Installation]. This completes the software installation. *For the DR-2050SP, the following accessories are included in addition to the above items. If you click [Typical Installation], all of the Next, you need to connect the scanner to your computer. ( STEP 4) DR-2050SP User's Guide Remote Control AAA Batteries (2) RGB Cable 7. Slide the roller lock lever towards the right, fit the lever feed roller into the hole on software is installed. If you want to select Presentation Mode Edition Mini D-sub 15 Pin x 2 which parts of the software to install, click Continued on back side (Length: 5 ft. (1.5 m)) the left of the roller (1), and push down the roller lock lever to lock the feed roller [Custom Installation]. shaft (2). 4. Click [Install]. Note 8. Close the roller cover. Make sure that the roller cover clicks into place. All of the currently displayed software is installed. To install only selected software, To use the feed roller, install it on the scanner. click [Back] and select [Custom Installation]. [STEP 2] "Removing the Packing Materials and Installing the Feed Roller" 5. Click [Next]. Documents can be prevented from feeding slantwise by installing the document 6. Read the software license agreement, and guide adapters on the document guides. ( STEP 5) click [Yes] if you consent to the conditions of The adjustment sheet is used to adjust the scanner when anomalies begin to the software. appear in scanned images. Store it in a safe place where it will not be lost. Installation of the scanner driver starts. The DR-2050 Setup Disc contains the "DR-2050C Scanner Driver", "CapturePerfect 3.0", and "OmniPage SE" made by Nuance Communications Inc. DR-2050C/DR-2050SP User's Guide p.17 "About the Setup Disc" Items included in this package are subject to change without notice. You must keep the machine's packaging and packing materials for storing or transporting the machine. After checking the package contents, you need to prepare the scanner 9. Gently push in the front unit on its left and right sides to close the front unit. for use. ( STEP 2) Make sure that the front unit clicks into place. Removing the Packing Materials and 10. Close the document feed tray and top cover. Installing the Feed Roller Document Feed Tray Top Cover Remove the scanner from the box, remove the orange tape and protective sheets from the scanner, and install the feed roller on the scanner body. 1. Peel off the four pieces of orange tape from the outer casing. 2. Open the document feed tray and remove the protective sheet. During scanner driver installation, the scanner driver and the Job Registration Tool are installed. The scanner is now ready for use. Next, you need to install the scanner software. ( STEP 3) Trademarks * Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries. * Microsoft Windows(R) is a registered trademark of Microsoft USA in the United States and other countries. * Other brands and product names used in this manual may be trademarks or registered trademarks of their respective companies. PUB. CE-IE-546 (c)2007 CANON ELECTRONICS INC.